|
FT 6000 Generic Control
Module
|
Model:
52164 |
☺ |
TP/FT-10 |
☺ |
EEPROM |
Features
-
On-board FT 6050 Smart
Transceiver Chip
-
Differential Manchester
encoded signaling for polarity insensitive network wiring.
-
Transformer-isolation
-
Supported Data Rate - 78
kilobits per second
-
Distances up to 500 meters max
for free topology, and up to 2700 meters max for doubly
terminated bus topology
-
Includes 64 KB I2C Serial
EEPROM memory, and support in-circuit programming
-
Low power consumption.
-
Compact Vertical Mount
Configuration
-
Common form factor makes
control modules interchangeable,
also a fast replacement of FT5000 Control Point Module
Overview
FT6000 Generic Control Point Module
(52164) is a simple and cost effective way to add LonWorks communication to
your embedded design. It may be used as standalone board or with
host MCU and ShortStack firmware.
The FT 6000
control module consists of a miniature circuit card containing
an FT 6050 smart transceiver chip, communications transformer,
crystal, serial EEPROM memory and a
connector for power, I/O, In-Circuit Programming and the
network. The small
size of the control module permits it to be mounted on or inside
an OEM's product, directly adjacent to the sensors, outputs, or
displays that the module will control.
Using this
control module can save hundreds of hours of development time
compared with designing custom modules. The control modules can
be integrated into a product with minimal additional safety
testing.
Specification
|
Microprocessor |
Neuron
FT6050 |
|
Transceiver Type |
FT-X3
(FTT-10A) |
|
Transceiver Bit Rate |
78kbps |
|
Crystal
Oscillator Clock |
10MHz |
|
Memory |
I2C
Serial 64KB EEPROM |
|
Data
Communication Type |
Transformer-isolated twisted pair |
|
Isolation Between Network and I/O Connectors |
0-60Hz (
60 seconds ): 1000VRMS |
|
0-60Hz (
continuous ): 277VRMS |
|
Typical
Supply Current |
25mA
receive, 40mA transmit |
|
Maximum
Nodes Per Channel |
64 (-40
to + 85DegC) |
|
Network
Wiring |
22 to
16AWG twisted pair |
|
Network
Length in Free Topology |
<1000m
maximum total wire with one repeater |
|
<500m
maximum total wire with no repeaters |
|
<500m
maximum node-node distance with no repeater |
|
Network
Length in Doubly-Terminated Bus Topology |
up to
2700m worst case |
|
Maximum
Stub Length in Doubly-Terminated Bus Topology |
3m |
|
Network
Bus Polarity |
Polarity
insensitive |
|
Power-down Bus Protection |
High
impedance when unpowered |
|
Supply
Voltage |
3V~3.6V |
|
I/O
Connector |
2*13 on
2.54mm centers |
|
Network
Connector |
One
terminator in free topology, two terminators in
doubly-terminated bus topology |
|
Operating Temperature |
-40 to
+85 DegC |
|
Non-operating Temperature |
-40 to
+85 DegC |
|
Operating Humidity |
25-90%
RH @ 50 DegC, non-condensing |
|
Non-operating Humidity |
95% RH @
50 DegC, non-condensing |
|
Dimensions |
L44mm x
W16mm x H30mm |
Configuration
|
Platform |
Custom |
|
Transceiver Type |
TP/FT-10 |
|
Neuron Chip Model |
36 ( = FT 6050 ) |
|
External Clock Speed |
10 MHz |
|
Clock Multiplier |
8 |
|
System Clock |
80 MHz |
|
System Image Version |
Default |
|
Firmware Version |
21 |
|
Off-Chip ROM |
N/A |
|
Extended Non-Volatile |
0x4000 to 0xC7FF |
|
Extended On-Chip RAM |
0xC800 to 0xE7FF |
|
I/O |
N/A |
|
On-Chip ROM |
0x0000 to 0x3FFF |
|
On-Chip RAM |
0xE800 to 0xEFFF |
|
Mandatory EEPROM |
0xF000 to 0xF7FF |
|
Extended On-Chip EEPROM
|
0 |
|
Non-Volatile Memory Type
|
EEPROM |
|
Pin |
Function |
Description |
|
1 |
GND |
Ground |
|
2 |
RST~ |
Reset (active
low) |
|
3 |
CP3_RXLED
|
RxActive for
network activity LED |
|
4 |
CP2_TXLED |
TxActive for
network activity LED |
|
5 |
NC |
No Connect
|
|
6 |
VDD3V3 |
3.3 V Input
Power |
|
7 |
GND |
Ground |
|
8 |
SCL
|
I2C serial
clock for in-circuit programming |
|
9 |
SDA_CS1~
|
I2C serial data
for in-circuit programming |
|
10 |
SVC~
|
Service (active
low) |
|
11 |
IO0
|
IO0 for I/O
objects |
|
12 |
IO1
|
IO1 for I/O
objects |
|
13 |
IO2
|
IO2 for I/O
objects |
|
14 |
IO3
|
IO3 for I/O
objects |
|
15 |
IO4
|
IO4 for I/O
objects |
|
16 |
IO5
|
IO5 for I/O
objects |
|
17 |
IO6
|
IO6 for I/O
objects |
|
18 |
IO7
|
IO7 for I/O
objects |
|
19 |
IO8
|
IO8 for I/O
objects |
|
20 |
IO9
|
IO9 for I/O
objects |
|
21 |
IO10
|
IO10 for I/O
objects |
|
22 |
IO11
|
IO11 for I/O
objects |
|
23 |
MOV_GND
|
Return (ground)
for MOV ESD clamp |
|
24 |
GND
|
Ground
|
|
25 |
FT_NETA
|
FT network
connection |
|
26 |
FT_NETB
|
FT network
connection |
-
Mechanical:
(Same as
CPM 5000
- Model No: 52124)
Order Information
| Order Code |
Description |
Unit Price (Euro)* |
| 52164 |
LonWorks 3.0 Control
Point Module CPM 6000 (or FT6000 Control Module) |
24.90 |
* Minimum Order Amount May Applied
Other Related Products
FT5000
Control Point Module 52124
FT3150
Control Module
52004
FTT Flash Control Module
52114
FTT Flash
Control Module 52994 (55020R-01)
Generic Core Module
53011
|
